news

한어Русский языкEnglishFrançaisIndonesianSanskrit日本語DeutschPortuguêsΕλληνικάespañolItalianoSuomalainenLatina

As we all know, the most important part of decoration is water and electricity renovation, because it is related to the quality of life in the future, as well as the safety of household water and electricity. However, most newcomers do not know how to identify whether the water and electricity renovation is qualified, and which areas the owners need to pay special attention to. Today, the editor invited a master with 30 years of decoration experience to teach on-site at the construction site, and newcomers can just follow the instructions!

Kitchen water and electricity

Refrigerator single control

Refrigerators basically run 24 hours a day without interruption. Only in this way can the food be kept fresh. However, sometimes some owners are not at home for several days. At this time, a single-control switch is needed to avoid the phenomenon that the refrigerator is also powered off when the main valve is closed.

Gas pipe not centered

Gas is relatively dangerous, so the material of the gas pipe must be the best. Generally speaking, the gas pipe should be located between the cold and hot water pipes, but the water pipe of the water heater must be installed behind it. Therefore, here, the editor recommends that the two gas pipes be placed on the right side and in the same groove as the cold water pipe, but it is best to be 2 cm apart in the middle.

Socket reserved

This detail is easily overlooked by many owners. If you don't install it, it will be very embarrassing to install a water purifier later. So be sure to reserve a socket!

Bathroom water and electricity

Toilet location

The location of the toilet must be determined in advance, and it should not be easily moved later, because the shower room is divided on the basis of locking the toilet location. Also, everyone should remember to install a socket next to the toilet to facilitate the replacement of a smart toilet in the future.

The female thread elbow of the shower room is fixed with a matching fixture, which is convenient for the later installation of the shower head. The sewer pipe opening also has a special protective cover, so there is no need to worry about construction waste falling into it.

Living room circuit

The height of the TV cabinet determines the socket

When installing the TV socket, we must determine the height of the TV cabinet in advance and determine the height and position of the socket according to this standard.

Wires should not go through corners when passing through walls

There are usually no sockets in the balcony, so you need to pull the wires. But this faces a problem. When we pull the wires, the wires will pass through the wall. If there are sockets in the corners, the balcony may leak. Therefore, it is recommended that you pass the wires through the wall above the ground, which will be safer.

Circuits in the bedroom

Bedside socket

The sockets here are determined according to the height of each bedside table. Generally speaking, it is more appropriate for the socket to be positioned about 25 cm higher than the bedside table.

This way of installation and use is particularly convenient, and there is no need to worry about water splashing into the socket after the cup is hit.

Corner reserved socket

Install a few sockets in the corners of the wall. In this way, if you want to use some small appliances in the future, such as electric fans, electric curling machines, etc., it will be very convenient.

Cloakroom circuit

Cloakroom exterior lighting

The cloakroom in my house is open. Since there is no light outside the cloakroom, we need to install a lamp outside so that the light will not be too dim.

Water and electricity decoration details

Generally speaking, it is best to run the wires in the kitchen and bathroom on the ceiling and fix them with pipe clamps. In order to prevent condensation, it is best to insulate the water pipes. Following the principle of power on and water off, the hot water pipes are above the cold water pipes. If you run on the ground, you can find out when the water pipes leak. If you run on the ground, the neighbors downstairs will suffer, and it is not convenient to repair.

Wall grooving precautions

1. It is easier to move up and down, and it is also easier to achieve verticality.

2. The vertical groove is conducive to the inspection and maintenance of the circuit. If nails are hammered into the wall in the future, the direction of the wires can be determined based on the socket, effectively preventing the pipes from being damaged.

3. Opening vertical grooves is simple and fast

Everyone must remember to ensure that all circuits are connected from beginning to end to prevent the occurrence of circuit crossover. The electrical box must be the end of the wire. Strong and weak electricity must be cross-shielded, the slots must be horizontal and vertical, and the corners must be made into large turns. In this way, if there is a problem in the future, it will be easy to repair.

The ends of the wires in the dark box should be covered with electric caps. After these are done, the dark box should be covered with a disposable cover to facilitate future inspection and maintenance.